News

FRP Grating Selection Guide: Structure, Thickness and Application Comparison

Oct. 22, 2026

FRP Grating Selection Guide: Structure, Thickness and Application Comparison

Selecting a grating typically comes down to two questions: what substances must it withstand, and what load must it bear? This article compares fiberglass-reinforced plastic (FRP) gratings with those made of metal or wood, breaks down various structural configurations and four standard thickness levels, and explains the ideal applications for each combination. 

1. FRP Grating vs. Metal and Wood

Metal grating and timber decking are still the right answer in some places. Where corrosion and humidity arrive together, however, both start to cost money after installation: steel needs derusting and repainting, timber absorbs water and loses section. FRP grating changes that balance because the material itself does not corrode.

Table 1 — Comparison of FRP, metal and wooden grating

Criterion

Metal grating

Wooden decking

FRP grating

Corrosion

Rusts in humid and chemical service; needs continuous protection

Absorbs water, rots and deforms

Corrosion-resistant in humid and chemical environments

Weight and installation

High density; lifting and handling costs

Lighter, but strength is limited

High strength-to-weight ratio; light and easy to handle

Load capacity

High strength, but section-dependent

Insufficient strength; ages in service

Four thickness grades to match the duty

Surface safety

Slip resistance relies on added treatment in wet areas

Splinters and becomes slippery as it wears

Frosted and covered options improve grip and contain falling objects

Maintenance

Periodic derusting and repainting

Periodic replacement

Low maintenance; lower lifetime cost

 

2. Various Structural Types, and the Problem Each One Solves

A standard panel cannot cover every duty, so the range is built in four constructions. The difference between them is functional, not cosmetic: each one answers a specific site problem.

Table 2 — Structural comparison of FRP grating types

Type

Structure

Problem addressed

Typical applications

Standard

Standard load-bearing mesh; all four thickness grades

General load-bearing duty with corrosion resistance

Walkways, platforms, trench covers, shelving

Frosted surface

Standard construction with a matte top surface

Slip resistance in wet or demanding areas

Car wash bays, stair treads, wet walkways

With cover

Integrated top plate forming a solid walking surface

Small objects falling through; closed working surfaces

Maintenance platforms, access walkways

Cross-reinforced

Internal cross supports inside the mesh

Higher strength and better load distribution

Vehicle-bearing areas, longer spans

FRP Grating Selection Guide: Structure, Thickness and Application Comparison

FRP Grating Selection Guide: Structure, Thickness and Application Comparison

FRP Grating Selection Guide: Structure, Thickness and Application Comparison

 

 

 

Figure 2 — Frosted surface, covered and cross-reinforced grating

Structure and thickness are independent choices, which is where most specifications go wrong. A 38 mm standard panel suits a walkway through a chemical unit; a 38 mm cross-reinforced panel is what a vehicle-bearing area needs.

 

3. Which Thickness Do You Need?

The four grades map onto applications rather than onto an abstract strength ranking. Thicker is not automatically better — it is heavier and more expensive, and some applications never need the extra section.

Table 3 — Thickness grades and typical applications

Thickness

Typical applications

25 mm

Pigeon breeding houses; tree pit covers for landscaping; pedestrian walkways; floor platforms; storage shelving

30 mm

Tree grates and tree pit covers; livestock farms; stair treads; drainage trench covers; walkways and car wash areas

38 mm

Car wash facilities; wastewater treatment plants; chemical plants; vehicle load-bearing areas; drainage covers

50 mm

Car wash drainage trenches; large-scale construction projects; chemical engineering facilities; offshore oil platforms; heavy-duty drainage systems

 

4. Cutting, Edge Finish and Accessories

Part of the delivered cost of a grating floor never appears in the resin or the glass fiber — it appears on the cutting bench. Five cutting configurations are standard, and the last four produce tooth edges, so the choice affects material loss, appearance and how the panel is closed off on site.

Table 4 — Cutting configurations and edge result

Method

Edge result

Typical use

Hemming all around

Square edge on all four sides

Panels exposed on every side

Three sides

Square edge on three sides

Panels set against a wall or kerb

Hemming on opposite sides

Square edge on two opposite sides

Runs joined in one direction

Adjacent sides

Square edge on two adjacent sides

Corner installations

Successive cutting method

Tooth edge on all sides

Edges concealed behind profiles

FRP Grating Selection Guide: Structure, Thickness and Application Comparison

Figure 3 — Even edge and tooth edge after cutting

What we can supply around the panel is equally practical:

▪  Thickness: 25, 30, 38 and 50 mm.

▪  Standard Sizes: 1 × 4.04 m, 1.22 × 4.04 m and 1.22 × 2.44 m, with custom sizes on request.

▪  Mesh Opening: 38 × 38 mm as standard; other openings can be produced to order.

▪ Cutting: panels cut to your installation dimensions; material loss during cutting may carry an additional charge.

▪  Colour: available on request.

▪  Accessories: grating clips and fasteners supplied to match the panel.

FRP Grating Selection Guide: Structure, Thickness and Application Comparison

                                                       Figure 4 — Grating clips and fasteners for panel connection

5. Specify in Three Steps

Step 1 — Fix the medium. Strong acids and alkalis point to pure resin construction. A conventional corrosive environment is served by glass fiber reinforced grating; there is no need to pay for a higher corrosion class than the process requires.

Step 2 — Size the thickness by load and span. Pedestrian and light duty sit at 25–30 mm, vehicle and plant areas at 38 mm, heavy engineering and offshore work at 50 mm. Long spans or concentrated loads call for the cross-reinforced construction.

Step 3 — Choose surface and edge last. Frosted finish for wet or wash-down areas, covered panels where small objects must not fall through, then an edge configuration based on whether the panel is exposed or concealed. Cutting loss belongs in the total price, not in a later surcharge.

6. About Us

Hebei Fortis Technology Co., Ltd. Supplies various FRP grating, and also manufactures pultruded FRP structural profiles and composite environmental products for customers in petrochemical, water treatment, power, construction, marine and agricultural sectors.

For more information, please contact our technical team.

Hebei Fortis Technology Co., Ltd.

TEL: +86 18932662725 / 19033312730

Email: allen@hbfortis.com

Contact us immediately to discuss your product project requirements

Contact Us

Contact Us

Tel.: +86 189 3266 2725

E-mail: sale@hbfortis.com

Add.: No.8-1, Zhenxing Street, Matun Town, Zaoqiang County, Hengshui City, Hebei Province

Get in Touch

Get in Touch

Copyright © Hebei Fortis Technology Co., LTD All Rights Reserved | Sitemap | Privacy Policy | Powered by